diff options
Diffstat (limited to 'net-analyzer/nagios-nsca/files/nsca.cfg')
| -rw-r--r-- | net-analyzer/nagios-nsca/files/nsca.cfg | 182 |
1 files changed, 0 insertions, 182 deletions
diff --git a/net-analyzer/nagios-nsca/files/nsca.cfg b/net-analyzer/nagios-nsca/files/nsca.cfg deleted file mode 100644 index e7e0402..0000000 --- a/net-analyzer/nagios-nsca/files/nsca.cfg +++ /dev/null @@ -1,182 +0,0 @@ -#################################################### -# Sample NSCA Daemon Config File -# Written by: Ethan Galstad (nagios@nagios.org) -# -# Last Modified: 06-10-2002 -#################################################### - - - -# PORT NUMBER -# Port number we should wait for connections on. -# This must be a non-priveledged port (i.e. > 1024). - -server_port=5667 - - - -# SERVER ADDRESS -# Address that nrpe has to bind to in case there are -# more as one interface and we do not want nrpe to bind -# (thus listen) on all interfaces. - -#server_address=192.168.1.1 - - - -# ALLOWED HOST ADDRESSES -# This is a comma-delimited list of IP address of hosts that are allowed -# to talk to the NSCA daemon. -# -# Note: The daemon only does rudimentary checking of the client's IP -# address. I would highly recommend running as a service under -# inetd instead of as a standalone daemon and using TCP wrappers to -# limit access. - -allowed_hosts=127.0.0.1 - - - -# NSCA USER -# This determines the effective user that the NSCA daemon should run as. -# You can either supply a username or a UID. -# -# NOTE: This option is ignored if NSCA is running under either inetd or xinetd - -nsca_user=nagios - - - -# NSCA GROUP -# This determines the effective group that the NSCA daemon should run as. -# You can either supply a group name or a GID. -# -# NOTE: This option is ignored if NSCA is running under either inetd or xinetd - -nsca_group=nagios - - - -# DEBUGGING OPTION -# This option determines whether or not debugging -# messages are logged to the syslog facility. -# Values: 0 = debugging off, 1 = debugging on - -debug=0 - - - -# COMMAND FILE -# This is the location of the Nagios command file that the daemon -# should write all service check results that it receives. - -command_file=/var/nagios/rw/nagios.cmd - - -# ALTERNATE DUMP FILE -# This is used to specify an alternate file the daemon should -# write service check results to in the event the command file -# does not exist. It is important to note that the command file -# is implemented as a named pipe and only exists when Nagios is -# running. You may want to modify the startup script for Nagios -# to dump the contents of this file into the command file after -# it starts Nagios. Or you may simply choose to ignore any -# check results received while Nagios was not running... - -alternate_dump_file=/var/nagios/rw/nsca.dump - - - -# AGGREGATED WRITES OPTION -# This option determines whether or not the nsca daemon will -# aggregate writes to the external command file for client -# connections that contain multiple check results. If you -# are queueing service check results on remote hosts and -# sending them to the nsca daemon in bulk, you will probably -# want to enable bulk writes, as this will be a bit more -# efficient. -# Values: 0 = do not aggregate writes, 1 = aggregate writes - -aggregate_writes=0 - - - -# APPEND TO FILE OPTION -# This option determines whether or not the nsca daemon will -# will open the external command file for writing or appending. -# This option should almost *always* be set to 0! -# Values: 0 = open file for writing, 1 = open file for appending - -append_to_file=0 - - - -# MAX PACKET AGE OPTION -# This option is used by the nsca daemon to determine when client -# data is too old to be valid. Keeping this value as small as -# possible is recommended, as it helps prevent the possibility of -# "replay" attacks. This value needs to be at least as long as -# the time it takes your clients to send their data to the server. -# Values are in seconds. The max packet age cannot exceed 15 -# minutes (900 seconds). - -max_packet_age=30 - - - -# DECRYPTION PASSWORD -# This is the password/passphrase that should be used to descrypt the -# incoming packets. Note that all clients must encrypt the packets -# they send using the same password! -# IMPORTANT: You don't want all the users on this system to be able -# to read the password you specify here, so make sure to set -# restrictive permissions on this config file! - -#password= - - - -# DECRYPTION METHOD -# This option determines the method by which the nsca daemon will -# decrypt the packets it receives from the clients. The decryption -# method you choose will be a balance between security and performance, -# as strong encryption methods consume more processor resources. -# You should evaluate your security needs when choosing a decryption -# method. -# -# Note: The decryption method you specify here must match the -# encryption method the nsca clients use (as specified in -# the send_nsca.cfg file)!! -# Values: -# -# 0 = None (Do NOT use this option) -# 1 = Simple XOR (No security, just obfuscation, but very fast) -# -# 2 = DES -# 3 = 3DES (Triple DES) -# 4 = CAST-128 -# 5 = CAST-256 -# 6 = xTEA -# 7 = 3WAY -# 8 = BLOWFISH -# 9 = TWOFISH -# 10 = LOKI97 -# 11 = RC2 -# 12 = ARCFOUR -# -# 14 = RIJNDAEL-128 -# 15 = RIJNDAEL-192 -# 16 = RIJNDAEL-256 -# -# 19 = WAKE -# 20 = SERPENT -# -# 22 = ENIGMA (Unix crypt) -# 23 = GOST -# 24 = SAFER64 -# 25 = SAFER128 -# 26 = SAFER+ -# - -decryption_method=1 - |